Raised-panel steel
Carriage house
Modern flush
Full-view glass
LiftMaster openers
Chamberlain openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the truck arrives.
Get your free estimateTrusted Garage Door Spring Repair for Houston Homeowners
When a garage door spring breaks in Houston, the door rarely fails quietly. You hear it from the kitchen, the driveway, or the bedroom – a sharp crack like a gunshot, then a door that will not budge. That spring carries the full weight of the door, and once it goes, the opener alone cannot lift it. Fernbrook Garage Doors Houston has repaired and replaced springs across Houston since 2002, so we know what you are dealing with and we do not waste your time. A live person answers our phone at (361) 286-8321 around the clock, and we can typically get a uniformed, background-checked technician to your home the same day. You will get a written price before we touch anything. No guesswork, no pressure.
Key Takeaways
- Garage door spring repair in Houston typically costs $180 – $340 depending on spring type and door weight.
- Springs have a limited cycle life. In Houston’s humidity, replacement springs can wear faster than drier climates.
- A broken spring means the door should not be forced open. That can bend tracks, damage cables, and strain the opener.
- Fernbrook technicians arrive with shoe covers, drop cloths, and a written price before any work begins.
- Every spring repair is covered by the 365-Day Done Right Promise.
Styles & brands we work with
Garage Door Spring Replacement
Garage Door Spring Replacement means removing the worn or broken spring (or springs) and installing a new one matched to your door’s exact weight, height, and cycle count. Most garage doors in Houston use either a torsion spring mounted above the opening or two extension springs running along the horizontal tracks, and each requires a different replacement approach. For homeowners in the area, our Garage Door Spring Repair in Houston covers both types. Fernbrook Garage Doors Houston handles both, and the work runs $180 – $340 in this market. The final number depends on spring type, whether we replace one spring or a pair, and your door’s weight class. We quote the full amount in writing before we start, so there is no surprise at the end.
When to Replace Instead of Repair
If the spring is broken, there is no repairing it; it has to be replaced. If only one of a pair has failed, we typically recommend replacing both because the second has logged the same cycles and will likely fail soon. The door will balance better with matched springs, and you will not pay a second service call a few months down the road.
What We Check Before Quoting
Before recommending a replacement, we weigh the door manually to confirm the spring rating, inspect the cables and bearings, and check the center bracket and spring pad for wear. A spring that is sized wrong will not last – even if the label says it is rated for the door. Our technicians are trained on Clopay and Amarr door systems, so we know how to match springs to door weight, not just door width.
Garage Door Torsion Spring Replacement
Garage Door Torsion Spring Replacement is the job most Houston homeowners need, because torsion springs are the standard on modern and heavier doors. The spring is mounted on a metal shaft above the door, and it stores torque to counterbalance the door’s weight. Torsion spring replacement at Fernbrook Garage Doors Houston runs $180 – $340, and the job includes calibrating the spring to the door’s exact weight so it opens smoothly without straining the opener. A torsion spring is under high tension, and the winding process is dangerous without the right bars and training. Do not attempt this yourself.
Torque and the Houston Problem
Heavy double doors and wood doors put more torque on a torsion spring, and Houston’s heat and moisture can shorten the spring’s coating life. We use rust-inhibiting, high-cycle springs where they are available, and we know how to set the wind count so the door neither slams nor floats. When the spring is right, the door should stay put halfway open without the opener holding it.
Single Spring or Two
Some doors have one large torsion spring; heavier doors usually have two smaller ones. If one of a pair breaks, we will quote you for both because the surviving spring has the same wear history and will not match the new one’s tension. Leaving an old spring next to a new one creates an uneven door, and that causes more problems than it delays.
Broken Garage Door Spring
Broken Garage Door Spring is the most common garage door emergency we see in Houston week to week. You will usually hear a loud bang from the garage, and then the door either will not open or opens a few inches and stops. At that point, forcing the opener to pull the door is a mistake. Fernbrook Garage Doors Houston replaces broken springs every day, typically the same day you call, and the job falls within our Garage Door Spring Repair in Manvel and Houston area $180 – $340 repair range. A technician will confirm what is broken, show you the failed spring, and give you a written price before replacing it.
The Morning Discovery
Most people notice the broken spring in the morning when the car is stuck in the garage and the kids are running late. That is why we keep our Houston schedule flexible; our dispatchers look for the soonest window and our techs arrive prepared with common spring sizes, cables, and rollers on the truck. One visit usually gets you from stuck to operational.
What a Broken Spring Means for the Door
A spring that snaps is not just an inconvenience – it changes the load on every other moving part. The cables can jump off the drums, the door can pull sideways, and the opener’s travel can force the panel into the header. We check all of these when we replace the spring, because they often happen within seconds of the failure, and the repair should address them before they cause another failure.
Garage Door Extension Spring
Garage Door Extension Spring refers to the stretch-type springs mounted above the horizontal tracks, one on each side of the door. They are more common on older one-car doors and some lighter aluminum doors here in Houston. Swapping out extension springs runs $180 – $340 with Fernbrook Garage Doors Houston, and the price includes balancing the door, checking the safety cables, and adjusting the pull so the door rises evenly on both sides. Extension springs lose tension gradually, so the signs are usually a door that feels heavy or hangs crooked.
Safety Cables and Why They Matter
Extension springs stretch when the door closes, and if a spring lets go, it can shoot across the garage. That is why we inspect and replace safety cables that run through the center of each spring. A safety cable catches the spring if it breaks and keeps it from hitting a car, a wall, or a person. If your door has older extension springs without safety cables, we will quote adding them as part of the repair.
Should You Convert to Torsion
On some doors, we will recommend converting from extension to torsion, which mounts the spring above the door and tends to be smoother and longer-lived. It is a bigger job, but if your door is heavy or sees daily use, the conversion often pays for itself in fewer repeat repairs. We will give you the numbers for both options and let you decide.
Garage Door Spring Installation
Garage Door Spring Installation means fitting a spring to a door that either has no spring, has a mismatched spring from a previous job, or is a new door that needs the spring set up correctly from the start. This is different from replacement because the goal is to establish proper balance and travel for a door that may never have worked smoothly. Fernbrook Garage Doors Houston charges $180 – $340 for most spring installations, and we include a full balance test and opener force check with the install. New springs need to be wound to the exact number of turns, not guessed at.
First-Time Setup and Rebuilds
We install springs on garage rebuilds when the old spring was missing, or on doors that were never balanced in the first place. A door with the wrong spring will strain the opener motor, chew through rollers, and eventually pull a panel out of alignment. We size the spring by weighing the door, not by reading the old spring’s label, because older doors often had the wrong spring installed years ago.
Why Cycle Rating Matters
Houston doors that open four or more times a day go through over 1,400 cycles a year. Standard springs are rated for about 10,000 cycles, but we can install high-cycle springs rated far higher, which is a good choice if your door is the main entrance to your home. We will show you the difference in cost and help you pick the spring that matches how your family actually uses the door.
Garage Door Spring Adjustment
Garage Door Spring Adjustment is what you need when the spring is not broken but the door is not behaving right – it slams on the way down, struggles on the way up, or sits crooked. The spring’s tension is off, and the fix is to add or remove winding turns and re-secure the set screws. Fernbrook Garage Doors Houston performs spring adjustments for $120 – $240, which is lower than a full replacement, but the door has to be secure while the adjustment happens. That means winding bars, not screwdrivers, and a tech who knows when a spring is too far gone to adjust safely.
Adjusting a Door That Drifts or Slams
If the door drops fast when you release it from the open position, the spring has likely lost a little tension and needs another quarter- or half-turn. This is a small job, but it has to be done precisely, because adding too much winding makes the door want to climb on its own. We make the adjustment and then run the door through ten full cycles to confirm the balance holds.
When Adjustment Is Not Enough
An adjustment works when the spring is still structurally sound but slightly out of tune. If the spring has visible rust, stretched coils, or a gap in the coil spacing, adding tension can be unsafe. In those cases, we will tell you straight that the spring is near the end of its life and quote a replacement rather than winding a worn spring tighter and hoping. You get the facts before you spend a dollar.
Brands We Service
Our Houston technicians train on eight major garage door brands, and we service every unit we meet. We are particularly familiar with Genie door systems, which pair with a lot of the openers in the area, and we stock common Genie parts on our trucks so the spring and related hardware get fixed in one visit. A Genie door that will not lift is often a spring problem rather than a motor problem, and we check both before quoting. We also see a lot of Clopay doors in Houston, especially in the master-planned communities where the original builders installed them. Clopay doors tend to have specific spring pads and bracket hardware, and we carry the replacement parts that match.
On the custom-home side, we work on Amarr and Wayne Dalton doors, which show up regularly in Katy, Sugar Land Garage Door Spring Repair areas, and the newer developments north of the city. Wayne Dalton spring systems sometimes use a torque tube rather than a traditional torsion shaft, and our technicians are trained on both setups so they arrive knowing what to look for. Whether your door is a Genie, Clopay, Amarr, or any other make, we can diagnose and price the spring repair on the spot.
See the difference
Before
After
Before
After
Before
AfterSigns You Need a Pro Right Now
- A loud bang from the garage. That is almost always a spring snapping, and the door is now too heavy for the opener to lift safely. Do not try to force it up, because the opener’s safety system is not rated for that load.
- The door opens a few inches and stops. The opener is working, but the door is not counterbalanced. Continuing to run it will strip the opener gear and wear out the motor fast.
- You see a gap in the spring coil. A visible separation or a two-inch gap in the spring above your head means the spring has broken in two. The door may still move with help, but it is unsafe and the spring needs replacing immediately.
- The door feels heavy when you pull the release handle. A properly balanced door should lift with one hand. If it feels like dead weight, the spring has lost its tension and the opener is doing all the work.
- Cables are loose or hanging. When a spring breaks, the cables often come off the drums, and a hanging cable can snag and bend the track. Loose cables with a broken spring mean the door should be left alone until a pro arrives.
Our Process, Step by Step
Step 1: Call, talk to a person, and get a window. You call (361) 286-8321 and a live person answers, not a phone tree. We ask where in Houston you are, what the door is doing, and when you need us there. For broken springs, we work hard to get you same-day service.
Step 2: The technician arrives and looks before touching. Your tech will ask before stepping through the house to the garage, and will put on shoe covers before entering. We inspect the spring, cables, bearings, and tracks first, and we measure the door’s actual weight before choosing a spring.
Step 3: You get a written price, and you approve it before we work. We write the cost down, with the spring and labor separated, and hand it to you. The price is the price. If we find something else while working, we stop and show you before adding anything.
Step 4: We do the work, then clean up completely. The spring goes in, the door gets balanced, the opener force is checked, and all ten cycles of travel are tested. When it is done, we sweep up the broken spring and old parts, and we photograph the clean floor before we leave.
Step 5: The 365-Day Done Right Promise is in writing. Every spring repair is covered by our 365-Day Done Right Promise. If it is not done right, we make it right – no negotiation, no fine print. You also get a copy of the written price and the work summary for your records.
How Much Does Garage Door Spring Repair Cost in Houston?
A typical garage door spring repair in Houston runs $180 – $340, and for that price you should get the spring, the labor, a balance test, and an opener force check. The exact number depends on the spring type, the door’s weight, whether one or two springs need replacing, and the cycle rating of the spring we install. A standard single torsion spring on a one-car door sits at the lower end; a pair of high-cycle torsion springs on a heavy double door sits at the higher end. If the cables, rollers, or brackets are damaged at the same time, those are priced separately, and we will give you that number before touching them.
Three things affect the price most: the spring’s cycle rating, the door’s weight class, and whether the job is a straight replacement or includes extra repairs. To avoid overpaying, ask for the price before the work starts, ask whether you are getting two springs when only one failed, and ask for the spring’s cycle rating so you know what you are buying. Our free estimate includes the full inspection, the written price, and the clean-up. You are not paying for the quote, and the price you approve is the price you pay.
Our Service Area Near Houston
We repair garage door springs across the Houston metro – inside the 610 Loop, the Energy Corridor, the Heights, Bellaire, and west through Katy and Sugar Land. We also cover League City, Alvin, Tomball, Atascocita, Dickinson, Manvel, San Leon, Santa Fe, and Mission Bend. For most of these areas, we can have a technician to your door the same day you call, often within a few hours. If you live in a nearby community, give us a call and we will give you a straight answer about timing. You can also read more about our Garage Door Spring Repair in Katy and Garage Door Spring Repair in Sugar Land pages if those are closer to home. For larger repairs or a new door, our home page links to everything we do.
Serving Houston, TX - Our Local Coverage Area
We’re based in the Houston area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked Questions About Garage Door Spring Repair in Houston
Garage door spring repair is the process of diagnosing a broken, worn, or out-of-balance spring and restoring the door’s proper counterbalance. In Houston, this usually means replacing a broken torsion spring, replacing extension springs, or adjusting a spring’s winding to correct a door that drifts or slams. Fernbrook Garage Doors Houston includes a full door inspection in every spring repair so you know the whole system is sound after the spring is addressed. Call (361) 286-8321 for a written quote, free of charge.
Most spring repairs in Houston take between 60 and 90 minutes from the time the technician starts. Replacing a pair of torsion springs on a heavier door may take closer to two hours. The same-day service window depends on our dispatch schedule for your part of Houston or nearby communities like Highlands, but a broken spring is our top priority and we move these jobs first. If you’re in that area, our Garage Door Spring Repair in Highlands team can respond quickly.
A spring repair job in Houston runs $180 – $340 in most cases, including parts and labor. Lighter doors and standard-cycle springs sit at the lower end, and high-cycle springs or double-spring systems at the higher end. Cable replacements, track fixes, or other concurrent repairs are quoted separately before we do them. Your exact price is written down and agreed to before any work begins, and the estimate is free.
Yes. Our Houston technicians train on eight major garage door brands, including Genie, Clopay, Amarr, and Wayne Dalton, and we carry common parts for these systems on our trucks. We can also service Chamberlain, LiftMaster, Craftsman, and Raynor doors and openers. If your door brand is not on the list, we can still source the right spring for it and handle the job correctly.
In most cases, yes. Broken springs are the highest-priority repair we handle, and we keep same-day slots open across Houston for this reason. A live person answers our phone 24 hours a day, every day, and when you call with a broken spring, we will get you the earliest available window in your area. Call (361) 286-8321 to find out today’s schedule.
Every spring repair we do in Houston is covered by our 365-Day Done Right Promise. If the spring or the work is not done right within that year, we make it right – no negotiation required. The spring itself carries a manufacturer’s warranty, and we will tell you exactly what is covered on the spring we install and for how long.
You do not need to do much. Clear a path to the garage, move vehicles out if you can, and move anything fragile or valuable away from the door area. If you have pets, we ask that they be inside or in a safe space while we work. Our technicians bring their own tools, shoe covers, and drop cloths, and they will ask before moving anything in the garage.
Schedule Your Garage Door Spring Repair Service in Houston Today
A broken spring will not fix itself, and the longer it sits, the more stress it puts on your opener and door panels. Call Fernbrook Garage Doors Houston at (361) 286-8321 for a free, no-obligation estimate over the phone. We will give you a straight answer on price, schedule the soonest Houston window we have, and send a uniformed technician who hands you a written price before the first part comes off. Same-day service is available in most of the metro, and a live person answers around the clock.
Written by Jesse Calder, Owner at Fernbrook Garage Doors Houston, serving Houston families with garage door spring repair since 2002.